HUAWEI CDMA BTS 3606 PDF

Default Re: Huawei CDMA E BTS Max Power??? HI I think it can be more than 20W because the RF board support MAX 60W. The 3rd Global CDMA Operation and Development Forum, themed. To illustrate this further, we can note that Huawei BTSCE power With Huawei latest CDMA BTS products, based upon the physical network. indoor type) and BTSAC (for outdoor type) are The complete series of CDMA BTSs, and relevant Thus, for the same traffic in a sector, a Huawei BTS.

Author: Doutilar Shajinn
Country: Papua New Guinea
Language: English (Spanish)
Genre: Sex
Published (Last): 8 January 2004
Pages: 299
PDF File Size: 2.79 Mb
ePub File Size: 12.73 Mb
ISBN: 397-4-64927-676-8
Downloads: 70390
Price: Free* [*Free Regsitration Required]
Uploader: Sakinos

Connect the two probes to the paint-free place of the base and the expansion bolt. Please feel free to contact our local office or company headquarters. Connect the other end to the DB9 socket of the power backplane.

Page 15 The packing case is in hauwei condition. Determine the length of the grounding cables according to their actual cabling path, that is, the route from the binding post of BTS cabinet to the wiring holes of the grounding protection bar of the cabinet. If the outer package is damaged or soaked; or the equipment is soaked and becomes rusty, stop unpacking and find the cause.

HUAWEI BTS INSTALLATION MANUAL Pdf Download.

Tighten the csma at the front face of the cabinet. Chapter 4 Installing Cables introduces the categories of cables installed on site, cable distribution methods, and procedures of connecting various cables in BTS cabinet. Got it, continue to print. Chapter 4 Installing Cables Thus, you do not need to install these cables on site. Conducting Insulation Test To conduct an hawei test, proceed as follows: To print the manual completely, please, download it.

  BERGER LAHR D550 PDF

Make sure the support is level and huawsi cross-fasten the bolts of the lower support to 45 N-m in-lb with a torque wrench. Comments to this Manuals Your Name.

Huawei BTS Baseband Subsystem

This section introduces how to install the power module and what to pay attention during the installation. Page 70 – Distributing Protection Grounding Cables Installing Other Functional Modules Normally, the fan box is installed upon delivery.

The packing case is in good condition. Make sure that all the power modules are well connected with the backplanes, and that other boards and modules such as the CTRM and CHPA are not inserted in the slots of the backplanes.

Start Position the cabinet Remov e the Watch out for the sharp edges on the RF fan panel during the installation of RF cables lest it hurt your fingers. Tools The following tools are required: Feed back the situation to the local Huawei Representative Office.

Enter cdmz from picture: When installing the RF cable, connect unused connectors to matching load and secure them. It is divided into six chapters: Administration Building, Huawei Technologies Co. The cabinet is placed upside down.

The antistatic floor height refers to the distance between the upper surface of the antistatic floor and the cement floor.

  AHMAD IBN AJIBA PDF

CDMA grows greener

To locate the support at the side of antistatic floor, proceed as follows: Huwaei following items must be checked Do not put the wooden case upside cvma. Fasten the three bolt sets in the following order: This chapter describes how to install and use these two types of DDF. Loosen the screw in the small round hole such as —48V connecting hole on the power input side of the terminal block using a flat-head screwdriver.

Mouse operation Action Description Press and hold the primary mouse button left mouse Select button by default.

To avoid damaging equipment inside, do not apply too much force. Figure illustrates the positions of installation holes for U-bar supports. Figure Installing a board 2 Tighten the screws clockwise on the front panel, as shown in Figure Insert the boards according to the names on the relevant nameplates to cdmq any mistake.

Page of 93 Go.

Outline Figure shows the outline of the lower support. This manual also for: Lead the cables into their corresponding cable-fixing troughs. Installing the Lower Support To install the lower support, proceed as follows: The power cable and the grounding cable are routed straight and bundled neatly.

To remove cabinet doors, do it in a reverse order.