AGMA 390.03 PDF

AGMA Gear Handbook Gear Classification, Materials and Measuring Methods for Bevel, Hypoid CNCL S/S BY AGMA * CONTAINS FOLDOUT. Buy AGMA A (R) Handbook – Gear Classification, Materials And Measuring Methods For Bevel, Hypoid, Fine Pitch Wormgearing And Racks . Jan 12, Buy AGMA GEAR CLASSIFICATION, MATERIALS AND MEASURING METHODS FOR UNASSEMBLED GEARS from SAI.

Author: Tygolkis Meztilrajas
Country: Ukraine
Language: English (Spanish)
Genre: Business
Published (Last): 22 January 2018
Pages: 281
PDF File Size: 17.87 Mb
ePub File Size: 16.67 Mb
ISBN: 246-3-72354-883-1
Downloads: 16108
Price: Free* [*Free Regsitration Required]
Uploader: Torr

This assured some harmony with existing international standards and eliminated the difficulties associated with interpolating non–linear values from the AGMA The pinion is restrained from rotational motion and the gear is rocked back and forth until the sides of the gear tooth slot touch agka sides of the pinion tooth.

Out–of–roundness may be caused by errors agmx machine tools, cutting tools, lack of rigidity in setup, hardness variation in the gear blank or heat treat distortion.

So establishing the pinion tolerances for index errors, runout, profile, lead, etc. However, a gear which is specified to an AGMA accuracy grade must meet all the avma tolerance requirements applicable to the particular accuracy grade and size as noted in tables 4 and 5.

Consistent improvement in parts The caliper is to simultaneously touch both sides of the tooth and the top land when the tooth is the correct size and the caliper is positioned at the mean cone distance see figure This is shown in figure H.

Bevel Gear Classification, Tolerances, and Measuring Methods

Double flank composite SF: The resulting gear has very small amounts of individual 40 Much of the needed information can be read directly from the analog graph as described above. The measured location is then compared to the specified coordinate and the error is calculated.

  JOSEPH EDMINISTER CIRCUITOS ELECTRICOS PDF

See figures 6 and 7. The specific tolerances for such gears are to be agreed upon by the buyer and sgma seller. It provides an indication of correct tooth shape both up and down the tooth profile and lengthwise on the tooth.

Library Menu

This figure, with the following discussion, is intended to show the basic kinematic and mechanical requirements of the equipment necessary to comply with this standard; it is not intended to imply that this is acceptable construction. Alternatively, the theoretical tooth surfaces might be those for a perfectly conjugate gear and pinion. Total cumulative pitch variation, Fp, is the sum of the maximum negative index variation subtracted from the maximum positive index variation.

Finally, carefully remove the tape, without smearing the contact pattern impression, and place on a pattern tape record sheet. Generally, the gear is cut to the theoretical size as measured by the gear tooth calipers and the pinion is then cut to provide the specified backlash.

Interpretation of the data obtained from this check provides an indication of the shape of the actual profiles, and provides a practical way of accurately measuring the amount of relative vertical displacement from the specified mounting position which the gears can withstand without causing load concentrations at the ends of the teeth.

See figure 12; NOTE: The CMM must be calibrated by a certified and approved method and must have a suitable environment. The phase difference of the two processed pulse trains is converted to an analog waveform proportional to variations in transmission motion. See annex B, figure B.

We have no amendments or corrections for this standard. This measurement, however, is influenced by both axial and radial runout.

  LEFEBURE WELY SORTIE IN E FLAT PDF

Item Detail – AGMA

This force needs to be uniform over the entire reading scale. Ground bushings, arbors or ball sleeve interference fit tooling may be considered for more accurate test results.

Thus, it is possible that a specific gear 3900.3 pass through the entire production process without ever having been measured. Practices and measurement methods are included which are recognized and accepted throughout the gear industry as being reliable. In the previous classification system AGMA By joining you are opting in to receive e-mail. Considerations for certain gearing applications may require a high degree of accuracy in the angular position of the teeth.

An accurate method is essential for calibrating the dial indicator or recording equipment over the working range; — Other considerations: Are you an Engineering professional?

Ama Digital Transformation may be defined in a number of different ways by analysts or enterprise software vendors. Backlash is affected by the mounting distance on which unassembled gears will be operated; the tolerance on mounting distance is generally toward increasing backlash.

Therefore, all slots are now machined to the same radius from the center of rotation, and are displaced from true angular position by varying small amounts. This is to be done in a manner which maintains a central contact on the profile top and bottom while the pattern blends to the heel end of the tooth.